>adsl
Usage: adsl start [--up] [--mod <a|d|l|t|2|p|e|m>] [--lpair <(i)nner|(o)uter>]
           [--trellis <on|off>] [--snr <snrQ4>] [--bitswap <on|off>] [--sesdrop <on|off>] [--sra <on|off>]
           [--CoMinMgn <on|off>] [--i24k <on|off>] [--phyReXmt <on|off>]
       adsl stop
       adsl connection [--up] [--down] [--loopback] [--reverb]
           [--medley] [--noretrain] [--L3] [--diagmode] [--L0]
           [--tones]
       adsl configure [--mod <a|d|l|t|2|p|e|m>] [--lpair <(i)nner|(o)uter>]
           [--trellis <on|off>] [--snr <snrQ4>] [--bitswap <on|off>] [--sesdrop <on|off>] [--sra <on|off>]
           [--CoMinMgn <on|off>] [--i24k <on|off>] [--phyReXmt  <on|off>]
       adsl bert [--start <#seconds>] [--stop] [--show]
       adsl afelb [--time (sec)] [--tones] [--signal <1/2/8>] 
       adsl qlnmntr [--time (sec)][--freq (msec)]
       adsl info [--state] [--show] [--stats] [--SNR] [--QLN] [--Hlog] [--Hlin] [--HlinS] [--Bits] [--linediag] [--reset][--vendor]
           [--cfg]
       adsl --version
       adsl --help

> atm
Usage: atm start [--cqs <size>] [--pqs <size>] [--bs <size>]
           [--bo <offset>] [--intf <port> <adsl|utopia|loopback>]
           [<level2>] [<negedge>]]
       atm stop
       atm operate pripkt [--add <group> <offset> <value> [<mask>]
           [--delete [<group>]] [--show [<group>]]
       atm operate tdte [--add <ubr|ubr_pcr|cbr|rtvbr|nrtvbr>
           [<pcr>] [<scr>] [<mbs>]] [--delete <index>] [--show [<index>]]
       atm operate intf [--state <port> <enable|disable>] [--show [<port>]]
           [--stats [<port>] [reset]]
           [--setlink <port> <linkstate> <linkrate>]
           [--settype <port> <adsl|utopia|loopback> [<level2>] [<negedge>]]
       atm operate vcc [--add <port.vpi.vci>
           <aal5|aal2|aal0pkt|aal0cell|aaltransparent> <tdte_index>
           <vcmux_routed|vcmux_bridged8023|llcencaps|other|unknown>]
           [--delete <port.vpi.vci>] [--addq <port.vpi.vci> <size> <priority>]
           [--deleteq <port.vpi.vci> <size> <priority>]
           [--addpripkt <port.vpi.vci> <group>
           [--deletepripkt <port.vpi.vci> <group>
           [--state <port.vpi.vci> <enable|disable>] [--show [<port.vpi.vci>]]
           [--stats [<port.vpi.vci>] [reset]]
       atm atmbondingeth <--enable|--disable>
       atm bondconninfo
     atm  traffic  <atm|ptm>
       atm --version
        --help

atm version 1.3
> brctl
commands:
        addbr           <bridge>                add bridge
        delbr           <bridge>                delete bridge
        addif           <bridge> <device>       add interface to bridge
        delif           <bridge> <device>       delete interface from bridge
        setageing       <bridge> <time>         set ageing time
        setbridgeprio   <bridge> <prio>         set bridge priority
        setfd           <bridge> <time>         set bridge forward delay
        sethello        <bridge> <time>         set hello time
        setmaxage       <bridge> <time>         set max message age
        setpathcost     <bridge> <port> <cost>  set path cost
        setportprio     <bridge> <port> <prio>  set port priority
        setportsnooping <bridge> <port> <addr>  set port snooping
        clearportsnooping       <bridge> <port> <addr>  clear port snooping
        showportsnooping        <bridge>        show port snooping
        enableportsnooping      <enable>                enable port snooping
        show                                    show a list of bridges
        showmacs        <bridge>                show a list of mac addrs
        showstp         <bridge>                show bridge stp info
        stp             <bridge> <state>        turn stp on/off
> ddns
ddns add hostname --username username --password password --interface interface --service tzo|dyndns
     remove hostname
     show
ddns --help> 
> defaultgateway

Usage: defaultgateway config auto
       defaultgateway config static <[<IP address>] [<interface>]>
       defaultgateway show
       defaultgateway --help
> dhcpserver

Usage: dhcpserver config <start IP address> <end IP address> <leased time (hour)>
       dhcpserver show
       dhcpserver --help
> dns

Usage: dns config auto

Usage: dns config static [<primary DNS> [<secondary DNS>]]
       dns show
       dns --help
> lan

Usage: lan config [--ipaddr <primary|secondary> <IP address> <subnet mask>]
                  [--dhcpserver <enable|disable>]
       lan delete --ipaddr <primary|secondary>
       lan show [<primary|secondary>]
       lan --help
> ppp

Usage: ppp config <port.vpi.vci> [<connection id>] <up|down>
       ppp --help
       connect or disconnect ppp
> remoteaccess  

Usage: remoteaccess <enable|disable> [--service <servicename>]
       remoteaccess show [--service <servicename>]
       remoteaccess --help

Usage: route add <IP address> <subnet mask> <[<gateway>] [<interface>]>
       route delete <IP address> <subnet mask>
       route show
       route --help
> wan

Usage: wan config <port.vpi.vci> [<connection id>]
       [--protocol <bridge|pppoe|pppoa|mer|ipoa>] [--encap <llc|vcmux>]
       [--vlan <vlan id>] [--state <enable|disable>] [--service <servicename>]
       [--firewall <enable|disable>] [--nat <enable|disable>]
       [--igmp <enable|disable>] [--qos <enable|disable>]
       [--username <username> --password <password>]
       [--pppidletimeout <timeout>] [--pppipextension <disable|enable>]
       [--ipaddr <wanipaddress> <wansubnetmask]
       [--dhcpclient <enable|disable>]
       wan delete <port.vpi.vci> [<connection id>]
       wan show [<port.vpi.vci>]
       wan --help <bridge|pppoe|pppoa|mer|ipoa>
> ping
BusyBox v1.00 (2008.11.19-08:05+0000) multi-call binary

Usage: ping [OPTION]... host

Send ICMP ECHO_REQUEST packets to network hosts.

Options:
        -c COUNT        Send only COUNT pings.
        -s SIZE         Send SIZE data bytes in packets (default=56).
        -q              Quiet mode, only displays output at start
                        and when finished.
> siproxd
siproxd <enable|disable|show>
siproxd --help

> tftp
BusyBox v1.00 (2008.11.19-08:05+0000) multi-call binary

Usage: tftp [OPTION]... tftp_server_ip

Update firmware image and configuration data from OR backup configuration
data to a tftp server.

Options:
-g      Get file. (Update image/configuration data)
-p      Put file. (backup configuration data)
-f      remote file name.
-t      i for image and c for configuration data.
> sntp
sntp -s server [ -s server2 ] -t "timezone"
     disable
     date
     zones
sntp --help> 
> vdsl

Usage: vdsl info